The Birkin

The Birkin
The finished article

Sunday, April 6, 2008

Remounting the Seats

With the racing seat in place, it became apparent that my head will be above the rollbar when I have my helmet on. Kinda defeats the purpose of having a rollbar in the first place, really, as in the event of a rollover my head will be ensuring the rollbar comes out unscathed. So yet again I'm copying an idea from Frank, and repositioning the seat to be a lot lower.

The standard car comes with a set of movable rails mounted to a steel frame - all up there's probably 4kg of steel in the driver and passenger seat mountings. In addition, they put the seat about 2 cm from the floor, and with the thickness of the seat, that puts you about 8 cm up. With the modifications, you can get this down to about 3cm. 5cm doesn't sound like a great deal, but it makes a huge difference to the feeling of being "one with the car".

The modification basically involves removing the subframe (held in by four bolts), and angle grinding the two rear mounting points. The two rear points have a lip on them which prevents the seat from sitting on the floor.

Next, fashion a base plate out of 3mm aluminium. 3mm ali is probably overkill, and overweight, however seeing as your butt is now that much closer to the ground, a little armour plating probably doesn't go astray ;-) Plus, it adds some stability to the seat, as the seat is mounted directly to the plate itself.

The next step is to position the plate. The plate needs to fit in between the rear mounting plates for the seat belts and the floor. This means that the base plate is held in place by the same bolts as the seat belts, which are strong 10mm bolts. In addition, the plate is bolted to the steel crossmember in the footwell.

With a few rivnuts in place, the seat now bolts to a strong base which drops the driver (and passenger now I've done the same to the other side) lower into the car.

The downside is that the driver seat is now basically fixed in place. However, we also fitted the standard driver seat to the base, and it turns out that Dad fits in quite nicely! So he'll still be able to drive it (if I let him ;-)

Saturday, March 15, 2008

Slow Progress

Well, today was another engine building day, but overall not terribly good progress. Mike has been dialling in the cams, but even with the key in the crank holding the toothed chain wheel in place, there's too much movement. We needed the harmonic (the bit that takes any harmonic vibrations out of the crank) in place to hold it all together, but that's off being cut down. So it all came to a grinding halt, to be picked up next weekend.

Adding to that, I think the water rail I have doesn't fit the engine - I can see where it should go, but there's a whole heap of engine block in the way that doesn't seem to have been catered for in the design of the rail. So something else to look at.

So a slow week once more, as I work through some minor tasks. I've fiited (one) clear plastic 3M sheet on the rear guard to protect against stone chips, made a small bracket to mount the ECU on, and redone some wiring in the front. But that's not a great deal to show for a week.

I think next week may be focussing in on a few other things, like more furniture and stuff ;-)

Monday, March 3, 2008

Camera Work

With the build nearing completion, I thought it would be a good time to look at how I'm going to record it's first steps into the real world, so I've bought a camera setup.

The best regarded setup at the moment (according to OzClubbies) is the Elmo SUV camera - it has a good resolution lipstick lens that you can mount onto the rollbar, and a simple, lightweight recording unit that you can stop and start with one button press. I bought the camera with 150cm cable, the rubber mounting and wide angle lens from Digital Camera Warehouse, who are also well recommended on OzClubbies.

What made it easier was that Frank also has one, so the trend of basically copying everything he does continues ;-)

At the time of writing, DCW has a damn good deal on these things, which make them cheaper than anywhere else on the planet as far as I can tell.....btw, no commercial relationship with them at all. And if they stuff up the delivery you'll be the first to know.


The camera will therefore provide me with some decent video to add to the blog as well as photos, so look out for those in future ;-)




Sunday, March 2, 2008

Putting it all back together

With the engine parts now back, the engine can start to come together. On the principle that I'm barely qualified to tighten a bolt, I've decided to allow someone else to assemble the explosive part of the car ;-)

So, Mike has come back to reverse the exercise of disassembly, and is putting it all back together. So far, the crank is back in, along with the pistons. At this stage it's all large things going back in, so progress is fast, however next weekend we're looking at the cams, belts and chains etc, which could take a little longer.

Some early photos:


I have an engine!

Yes, the big news over the weekend is that the engine is back from the workshop, with the head ported and polished, the crank keyed, and the pistons flycut.....

So, what does that all mean? Well, porting the head means cutting away additional material from the part where the air gets into and out of the engine - again, one of the most important things for an engine to develop peak power is it's ability to breath, so removing any barriers or inefficiencies (such as rough patches, edges etc) will always yield results. The thing with the Duratec head is that it's pretty perfect as it stands. So, unlike the Zetec which was also cut for another Birkin (where a huge amount of material was removed), the Duratec is more of a polish. The key element is that the ports allow the right volume of air to flow based on the size of the valves, so there's no restriction in the head. Also, the split between the two chambers has been cut to a knife edge to reduce turbulence.

Keying the crank has been discussed before, and as you can see in the photo, it's a simple matter of notching the gear and putting a small key in the crank itself. Now, the gear cannot move on the shaft. Given the revs and power I have, I've read that it's probably overkill, but what the hell....




The pistons were apparently the hardest part. As you can see in the photo's, not a great deal of material was removed, which is what you're aiming for, as wholesale shredding of the piston heads is to be avoided. So you can see that there are now four small scallops taken out of each piston, which will allow the clearance required by the new, more aggresive cams.

All in all some nice work that will allow the engine to reach it's peak performance once it's all back together.

Thursday, February 28, 2008

Racing Seats

One of the tasks I had put aside for a rainy day, but thought I may as well do now as I have the time, is to install the racing seat.

Basically, the reasoning behind a racing seat is that it holds the driver in place better than the standard seat. In normal road use, this isn't a problem, however under the stresses of track use, a better seat is required.

I've bought a 15 inch Road / Race seat from Go Gear (www.gogear.com.au). The seat itself is an aluminium seat with a foam cover - pretty basic, but it fits into the Birkin with some modifications. So, I go out and spend over $600 on a seat, and then attack it with a sledgehammer.

To get the seat to fit, you need to bend the right hand shoulder wing in, as it doesn't clear the side of the car. Then you do the other side so it doesn't look to lopsided. Then you sit in it and work out that you don't fit anymore....so you hit it a few more times.

I also ground off the welds underneath the seat, removed a few studs, and bash in the side support around the base to give more clearance for the base. And it all fits in fine! I've also removed the sliders under the seat, and mounted the new seat to rivnuts put into the seating frame itself.

The seat means that I'm now really, really, held into the car, plus I'm a lot lower. I've also had to move the pedal box once more, as I'm also a lot further back in the car than before.

I'm also still waiting for the engine parts to come back, but again I'm expecting them this weekend.

Saturday, February 9, 2008

And now the front end

With the back end mostly done, attention switches to the front end. Basically the nosecone can now get fitted up, and the front indicators installed.

The first thing is putting the Birkin badge on the nose - pretty simple, but the black and silver looks really good against the green, and matches the rest of the car.

Getting the front indicators on is another matter. The indicators have to be within a certain distance from the outer edge of the car, which for the Birkin is the front wheel. To get these on, you have to drill two 10mm holes in the fibreglass nose - however the fibreglass is pretty brittle, and tends to shatter and flake, taking the paint with it. I drilled a few pilot holes, and luckily the damage to the paint isn't too bad (it's covered by the washer). But there's another thing I should have done before painting....

I also had a shot at putting the bonnett clips back on using stainless rivets, however got the size completely wrong and had to drill them all out. This worked well apart from the last two, so I've managed to gouge the aluminium skin a little. It'll be covered by the latch when it goes on again, but it looked pretty dodgy for a while there.

Anyway, more photos to be added.

And an update on the engine - delivery of all the parts promised for the end of next week ;-)